ALPHA2 25-60 N 130

Grundfos ALPHA2 high-efficiency circulator pumps are designed for circulating liquids in heating systems. The stainless-steel variant of the ALPHA2 is suitable for e.g. domestic hot-water systems. With an energy efficiency index (EEI) well below the ErP benchmark, it ensures substantial energy savings. Flow range : <3m³/h Lift range : ≤6m Maximum working pressure : 10bar liquid temperature : -25 .. 110 °C Aplication field : Is a household hot water system circulation pump equipped with a stainless steel pump casing. AUTOADAPT will enable the water pump to continuously adapt to the system, achieving optimal adaptability and low energy consumption.

The AUTOADAPT function continuously adapts the pump performance to the actual heat demand, i.e. the size of the system and changing heat demand during the year. The AUTOADAPT feature finds the setting that provides optimal comfort with minimal energy consumption and makes the commissioning fast, safe, and easy. ALPHA2 also offers proportional-pressure, constant-pressure and constant-curve control modes.

The Grundfos ALPHA2 is designed to drive the circulation of media in heating systems. Stainless steel pump heads can also be used for household hot water systems.
Grundfos ALPHA2 is suitable for the following systems:
1.The system needs to match actual needs by changing the operating point of the water pump
2.System of flow and temperature changes
3.A system that requires nighttime deceleration
Pump liquid
This pump is suitable for the following media:
1.Clean, thin, non corrosive, non explosive liquid, free of solid particles or fibers.
2.Cooling liquid without mineral oil.
3.Domestic hot water (tap water), with a hardness not exceeding 14 ° dH, a temperature not exceeding 65 ° C, and a short-term peak value not exceeding 70 ° C. The dissolved calcium in tap water should not form scale.
4.Water softening.
Automatic nighttime deceleration
The Grundfos ALPHA2 can choose to activate the automatic deceleration function at night.
The automatic deceleration at night can be activated through the buttons on the panel.
Factory settings: not enabled.
Note: If the pump is set to constant speed I, II, or III, the night time automatic deceleration function cannot be used.
When the night automatic deceleration function is activated, the pump will automatically switch between night deceleration mode and normal working mode. The switching depends on the pipeline temperature measured by the built-in temperature sensor.
function
When enabling the automatic deceleration function at night in the system, the pump must be installed on the pipeline.
The switching between normal operation and nighttime deceleration mode is determined by the temperature of the pipeline.
When the pipeline temperature exceeds 10 ° C to 15 ° C for about 2 hours, the pump will automatically switch to the night time automatic deceleration mode. The rate of temperature decrease must be at least 0 1 ° C.
When the pipeline temperature rises by about 10 ° C, the pump switches back to normal operating mode, which does not depend on time.
install

In the vast majority of installation scenarios, the Grundfos ALPHA2 only requires mechanical installation and then power on. When installing the water pump, the motor shaft must be kept horizontal.

. Located in Tianjin, China, Tianjin Shiny-Metals Technologyco., Ltd. is a professional company that specializes in the research and development, design, production, sales, trade, and service of pumps. Our products are exported to more than 40 countries and regions, continuously building our global brand reputation. We offer a wide range of pumps, including centrifugal pumps, axial flow pumps, jet pumps, submersible pumps, deep-well submersible pumps, and swimming pool pumps, with over 500 specifications available. Our company has obtained the ISO 9001 certification from the International Organization for Standardization (CQC). In addition, our civilian motors have undergone product evaluation for CCC China mandatory certification. We have also received certifications such as CE, EMC, GS, RoHS, EAC, SASO, and ST. Our company is dedicated to meeting customer needs with high-quality products, reasonable prices, and exceptional pre-sales, in-sales, and after-sales services. We adhere to the management principles of "quality first, customer first, and reputation-based" and are committed to providing global customers with the best solutions for water pumps and water treatment systems, improving their quality of life. Our goal is to make the world a better place through water, and we strive to make water even better.